GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 211

Страница: 211 / 236

Disassembly and reassembly

203

2062973-003

12.2.15 Replacing the alarm light board (FRU)

Disassemble first:
a.

12.2.6. Detaching the front unit and mid-frame assembly from the rear unit assembly

1. Remove the screw cover plate at the bottom

of the front panel.

2. Remove the two screws (T10) holding the front

unit assembly to the mid-frame assembly.

3. Detach the alarm light board cable from the

DC/DC board.

4. Release the four snaps - two on each side -

that mount the front unit assembly to the
mid-frame assembly to be able to detach the
alarm light board and detach the alarm light
board.

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Бренды по названию

Популярные бренды