GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 236

background image

CARESCAPE Monitor B450

104

2062973-003

8.2.5 Earth leakage current test

This test measures the current leakage flowing from the mains part through or across the
insulation into the protective earth conductor of the device under test.
Perform this test both in Normal Condition (NC) and in a Single Fault Condition (SFC), where one
of the supply conductors is open at a time. Perform the test with normal and reverse polarity.
NOTE: Refer to the instructions delivered with the safety analyzer to perform this test.

NOTE: *The measuring device (MD) represents the network and voltage measuring instrument
and its frequency characters according to IEC 60601-1.

1.

Configure the safety analyzer as follows (NC):

−

Polarity: NORMAL

−

Neutral: CLOSED

2.

Power on the device under test.

3.

Read and record the current leakage indicated on the safety tester.

4.

Configure the safety analyzer as follows (SFC):

−

Polarity: NORMAL

−

Neutral: OPEN

5.

Read and record the current leakage indicated on the safety tester.

6.

Configure the safety analyzer as follows (SFC):

−

Polarity: REVERSED

−

Neutral: OPEN

7.

Read and record the current leakage indicated on the safety tester.

8.

Configure the safety analyzer as follows (NC):

−

Polarity: REVERSED

−

Neutral: CLOSED

«
...
110
111
112
113
114
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: Datavideo Страницы: 50

Бренд: Waterous Страницы: 90

Бренд: Campbell Страницы: 14

Бренд: Keithley Страницы: 32

Бренд: jcb Страницы: 166

Бренд: Tascam Страницы: 80

Бренд: Tascam Страницы: 2

Бренд: Walker Страницы: 24

Бренд: Abicor Binzel Страницы: 92

Бренд: ECE Страницы: 2

Бренд: Ecco Страницы: 5

Evolution Series

Бренд: Bakare Страницы: 38

Бренд: Gatekeeper Страницы: 8

Bure Rise & Go DB 56-309

Бренд: Gate Страницы: 8

Бренд: Yamaha Страницы: 126

DM 2000 Version 2

Бренд: Yamaha Страницы: 8

Бренд: Bartscher Страницы: 20

Бренд: Bartscher Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды