GBC ORCA-I Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 56

GBC ORCA-I Скачать руководство пользователя страница 51

ORCA-I Operation Manual

Warranty



GBC Pro-Tech 1997 October

5-1

6HFWLRQ

:DUUDQW\

/LPLWHG :DUUDQW\

GBC Pro-Tech Engineering Company, Inc. warrants
the equipment sold is free from defects in material
and workmanship for a period of one year (1) from
the date of delivery to the customer. This warranty
is the only warranty made by GBC Pro-Tech and
cannot be modified or amended.

GBC Pro-Tech’s sole and exclusive liability and
the customer’s sole and exclusive remedy under
this warranty shall be, at GBC Pro-Tech’s option,
to repair or replace any such defective part or
product. These remedies are only available if GBC
Pro-Tech’s examination of the product discloses to
GBC Pro-Tech’s satisfaction that such defects
actually exist and were not caused by misuse,
neglect, attempt to repair, unauthorized alteration
or modification, incorrect line voltage,
contaminated air supply, or by fire, accident,
flood, or other hazard.

This warranty specifically does not cover damage to
the laminating rollers caused by knives, razor blades,
other objects that contact the rollers, neglecting to
clean the laminator, overheating the rolls, and failure
caused by adhesives or improper use of the machine.
Warranty repair or replacement does not extend the
warranty beyond the initial period from the date of
delivery.

CAUTION

Unauthorized customer alterations will void

this warranty.

THE WARRANTY MADE HEREIN IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING ANY WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. GBC PRO-TECH
WILL NOT BE LIABLE FOR PROPERTY
DAMAGE OR PERSONAL INJURY (UNLESS
PRIMARILY CAUSED BY ITS NEGLIGENCE),
LOSS OF PROFIT OR OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT
OF THE USE OR INABILITY TO USE THE
EQUIPMENT.

([FOXVLRQV WR WKH :DUUDQW\

This warranty specifically does not cover:

1.

Damage to the laminating rollers caused by
knives, razor blades, other objects that contact
the rollers, neglecting to clean the laminator,
overheating the rolls, and failure caused by
adhesives or improper use of the machine.

2.

Damage to the machine caused by lifting, tilting,
and/or any attempt to position the machine other
than rolling on the installed casters on even
surfaces.

3.

Improper use of the machine.

EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500

«
...
49
50
51
52
53
...
»

Содержание ORCA-I

























































Отзывы:

Нет отзывов