manualshive.com logo in svg

Gateway E-842R, Руководство пользователя

Поделиться
Скачать
Gateway E-842R Скачать руководство пользователя страница 138

APPENDIX B: Event Logs

www.gateway.com

132

Power supply <

zz>

 is not 

installed.

Error
[0xC6B 
(3179)]

The power supply was 
removed.

Re-insert the power 
supply, connect the AC 
power cord and power 
on the power supply.

Fan <

zz>

 is OK.

Information
[0xC6C 
(3180)]

Normal condition 
reported.

No action necessary.

Fan <

zz>

 is in a critical state.

Error
[0xC6C 
(3180)]

A specific fan failure.
Total fan failure.
Cooling fan module 
was removed.

Replace the cooling 
fan module.
Replace the cooling 
fan module.
Reinsert the cooling 
fan module.

Temperature sensor <

zz

> is 

OK.

Information
[0xC6D 
(3181)]

Temperature sensors 
are reporting normal 
temperatures in the 
enclosure.

No action required.

Temperature <

zz>

 is 

operating outside of 
specifications.

Warning
[0xC6D 
(3181)]

Temperature sensors 
are reporting 
enclosure 
temperatures have 
reached the threshold 
of 50°C.

Ensure that both 
cooling fans are 
operating normally. 
(Replace if needed.)
If the fans are set to 
automatic speed 
control, place the 
jumper on the Cooling 
fan module circuit 
board to force the fans 
to high speed.
If the environment 
ambient temperature 
is high, reduce the 
ambient temperature.
Ensure that the airflow 
is not blocked or 
restricted on the 
enclosure.

Temperature sensor <

zz>

 is 

in a critical state.

Error
[0xC6D 
(3181)]

Temperature sensors 
are reporting 
enclosure 
temperatures have 
reached the threshold 
of 70°C.

Automatic system 
shutdown begins. In 
Active-Active 
configurations, one 
controller shuts down 
its partner and 
shutdown the drives, 
then itself.
Ensure that both 
cooling fans are 
operating normally. 
(Replace if needed.)
If the fans are set to 
automatic speed 
control, place the 
jumper on the Cooling 
fan module circuit 
board to force the fans 
to high speed.

Enclosure Event Messages

Type [ID]

Cause

Action

Содержание E-842R





































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды