Gateway E-5400 Скачать руководство пользователя страница 100

Страница: 100 / 130

Peripheral/Adapter problems

The diskette drive will not read, write, or format

The diskette drive LED illuminates continuously

An adapter card is not recognized by the system

Probable Cause

Solution

The diskette is not
IBM-formatted.

Make sure that the diskette you are trying to
format is IBM compatible. If it is, try
reformatting it.

The disk is write
protected.

Make sure that the write-protection window on
the upper-right corner of the diskette is closed
(unprotected).

The diskette is
corrupted.

Run ScanDisk on the diskette. If errors are
detected and corrected, try accessing the
diskette again.

Probable Cause

Solution

The diskette is
corrupted.

Remove the diskette from the drive. If the light
remains on, try restarting the system.

The cable to the drive is
not connected properly.

Open the system, then check the cable
between the diskette drive and its controller.
Make sure that the pins are not bent or
misaligned.

Probable Cause

Solution

The interrupt and/or I/O
address is set
incorrectly.

Check the address configuration of the
adapter card and make sure that it does not
conflict with another card in the system.

The card has not been
configured through the
software.

Configure the card with the appropriate
software.

The card was not
installed correctly.

Reseat the card, then make sure that its
jumpers are configured appropriately.

05030.book Page 93 Monday, November 22, 1999 8:23 AM

Содержание E-5400



































































































































Результаты поиска

Содержание E-5400

Отзывы:

Бренды по названию

Популярные бренды

Gateway E-5400, Системное руководство

Результаты поиска

Содержание E-5400

Отзывы:

Бренды по названию

Популярные бренды