Gateway E-4400 страница 83 Скачать руководство пользователя

Страница: 83 / 118

Troubleshooting

Memory/processor problems

Memory errors were detected during system start up

A new processor is not recognized by the system

Probable Cause

Solution

Memory was added or
removed, and the new
configuration was not
saved in BIOS Setup
utility.

Enter the BIOS Setup utility and save the new
memory configuration.

The memory was
installed incorrectly.

Check the memory for proper seating and
orientation.

A memory chip is faulty.

Replace the card on which the faulty chip
resides. Third-party diagnostic programs can
help determine which chip or memory segment
is failing.

Probable Cause

Solution

The processor was
installed incorrectly.

Check the installation. The processor should
be recognized automatically if it was installed
correctly.

The processor speed
was not set correctly in
the BIOS Setup utility
configuration mode.

If your system BIOS lets you to select the
processor speed, make sure you have
selected the correct speed.

The processor was not
seated correctly in the
socket.

Make sure the processor is fully seated in its
socket.

Содержание E-4400























































































































Результаты поиска

Содержание E-4400

Отзывы:

Похожие инструкции для E-4400

Бренды по названию

Популярные бренды

Gateway E-4400, Системное руководство

Результаты поиска

Содержание E-4400

Отзывы:

Похожие инструкции для E-4400

Бренды по названию

Популярные бренды