Gateway E-4400 страница 58 Скачать руководство пользователя | Manualshive

Страница: 58 / 118

background image

Setting the system board jumpers

51

Setting the system board jumpers

The J5K1 configuration jumper on the system board lets you clear passwords
and recover the BIOS. (See the figure on page 5 for the location of the jumper.)
The table below shows the settings required to perform those tasks. Make sure
you turn off the computer and unplug the power cord before moving the
jumper.

Recovery mode

If you are trying to update the BIOS and have a problem such as a power
outage, the update may not be successful. You can then attempt to recover
the BIOS by setting the J5K1 jumper.

When you are attempting to recover the BIOS, no image appears on your
monitor.

Caution

Moving the jumper while the computer’s power is on can
damage your computer. Always turn off the computer and
unplug the power cord from the computer before changing
the jumper.

J5K1 Mode

Jumper
Setting

Action When Set

Normal

Pins 1-2

Normal operation

Configure

Pins 2-3

Adds a Maintenance menu to
BIOS Setup utility with options to
clear passwords

Recovery

No jumper

Causes computer to attempt
BIOS update or recovery from
diskette

«
...
56
57
58
59
60
...
»

Содержание E-4400























































































































Отзывы:

Нет отзывов

Похожие инструкции для E-4400

Бренд: Vecow Страницы: 144

Бренд: Stage right Страницы: 12

Бренд: Oval Страницы: 18

Бренд: Gateway Страницы: 346

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 1

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 2

Equium 7300S SERIES

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды