Gateway E-4400 страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 118

background image

Preparing to replace or add a drive

23

■

If only one drive is attached to a controller cable, configure the drive as
single if it is a hard drive or master if it is a CD drive. If two drives of
any type are attached to the cable, configure one as master and one as
slave.

■

You may need to configure the drives you install using the BIOS Setup
utility program. Press F1 at start up to access the BIOS Setup utility
program.

Drive cabling information

Three drive cables are included with your system. The diskette drive connector
cable is used to connect diskette drives and other non-IDE devices such as
tape backup drives. The two IDE connector cables are used to connect IDE
devices such as CD drives and hard drives.

If you want to add additional drives, you can replace the drive connector
cables with ones that contain three connectors, which would let you add a
total of four IDE devices or two diskette drives.

Important

If you choose to buy another IDE or SCSI hard drive, you
must also buy the appropriate IDE or SCSI controller card.

Diskette Drive
Connector Cable

IDE Connector Cables (two cables)

To floppy

connector on

riser card

To diskette

drive that

came with

your system

Black to connector
on IDE drive

80 wire cable

40 wire cable

Black to
secondary
IDE connector
on riser card

Blue to
primary IDE
connector
on riser
card

Black to connector
on CD drive

«
...
28
29
30
31
32
...
»

Содержание E-4400























































































































Отзывы:

Нет отзывов

Похожие инструкции для E-4400

Бренд: Tandy Страницы: 82

Бренд: Compaq Страницы: 18

Бренд: Radio Shack Страницы: 276

Бренд: UCOM Страницы: 3

FPMA-MOBILE1800

Бренд: New Star Computer Products Страницы: 4

Бренд: Aaeon Страницы: 117

BX-951-DC series

Бренд: Contec Страницы: 111

Бренд: Acer Страницы: 48

Бренд: Acer Страницы: 68

5535-5050 - Aspire

Бренд: Acer Страницы: 11

Бренд: Acer Страницы: 24

Бренд: Acer Страницы: 24

Бренд: Acer Страницы: 22

Бренд: Acer Страницы: 117

Бренд: Acer Страницы: 108

AcerPower S series

Бренд: Acer Страницы: 53

Бренд: Acer Страницы: 113

Бренд: Acer Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды