Gateway E-4400 Скачать руководство пользователя страница 10

Страница: 10 / 118

Rear panel

Rear panel

The desktop case rear panel includes the following Input/Output (I/O) ports,
connectors, and switches:

Kensington lock slot

permits the use of a cable lock to secure the system.

Keyboard port

connects a Personal System/2

(PS/2) compatible keyboard.

Microphone-in, Line-out, and Line-in audio jacks

connect audio devices

such as speakers, tape players, and microphones.

Mouse port

connects a PS/2-compatible mouse.

Parallel (printer) port

connects a printer or other parallel device.

Power connector

connects the computer power cord. The other end of the

power cord plugs into an AC outlet or power strip.

RJ-45 LAN connector

lets you connect to a network, and the

Indicator LEDs

show LAN activity (yellow LED) and 100 Mb/sec speed (green LED.)

Serial ports

connect to serial devices.

Thumbscrew

must be loosened to remove the cover from the system.

USB ports

connect external Plug-and-Play devices.

Voltage selector

sets the voltage for your area, either 115 V or 230 V.

Video port

connects the monitor’s interface cable.

Serial port 1

Keyboard port

Line-in

Microphone-in

Power connector

RJ-45 LAN connector
and indicator LEDs

USB ports

Voltage selector

Parallel (printer) port

Video port

Kensington lock slot

Thumbscrew

Mouse
port

Line-out

Serial port 2

Содержание E-4400























































































































Результаты поиска

Содержание E-4400

Отзывы:

Бренды по названию

Популярные бренды

Gateway E-4400, Системное руководство

Результаты поиска

Содержание E-4400

Отзывы:

Бренды по названию

Популярные бренды