Gateway 930 series Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 160

background image

38

Replacing and Adding System Components

Replacing a hot-plug drive

The hot-plug drives are located at the bottom of the front panel. The hot-plug
bay supports as many as six 1-inch high 3.5-inch SCA-II SCSI hard drives.

The hot-plug drives are assigned SCSI ID numbers by the hot-plug backplane
with the drive at the far left side of the hot-plug bay assigned SCSI ID 0. The
backplane assigns SCSI IDs to the other drives in order up to SCSI ID 5 at the
far right side of the hot-plug bay.

Install the drive in the left-most drive bay first and in increasing order by SCSI
ID number thereafter.

Important

Gateway tests and verifies the operation and compatibility
of the drives it sells. Especially in a hot-plug or
mission-critical environment, additional or replacement
drives must conform to Gateway standards.

SCSI ID 0
SCSI ID 1
SCSI ID 2
SCSI ID 3
SCSI ID 4
SCSI ID 5

8508088.book Page 38 Thursday, November 1, 2001 9:35 AM

«
...
44
45
46
47
48
...
»

Содержание 930 series

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 930 series

Бренд: N-Tron Страницы: 55

Бренд: IBM Страницы: 10

SUPERSERVER 2048U-RTR4

Бренд: Supermicro Страницы: 152

Бренд: Goonas Страницы: 13

Бренд: Yawarra Страницы: 4

callpilot 1002rp

Бренд: Avaya Страницы: 150

UniServer R4300 G6

Бренд: H3C Страницы: 542

Eternus DX80 S2

Бренд: Fujitsu Страницы: 186

Бренд: Fujitsu Страницы: 242

Бренд: HP Страницы: 94

Integrity rx5670

Бренд: HP Страницы: 46

Бренд: HP Страницы: 98

NetServer AA 4000

Бренд: HP Страницы: 82

Бренд: HP Страницы: 25

HPE ProLiant ML30 Gen9

Бренд: HP Страницы: 112

Бренд: HP Страницы: 28

Бренд: HP Страницы: 56

Hyper Converged 380

Бренд: HP Страницы: 125

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды