Gateway 930 series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 160

background image

12

System Features

Front panel board

The front panel board supports the LEDs and buttons accessible from the front
panel.

Power LED

glows green whenever the system is turned on. The LED also

flashes when the system is in sleep mode.

Disk activity LED

glows green whenever a hard drive is actively reading or

writing data.

System fault LED

(steady yellow) indicates an uncorrectable ECC memory

system fault, a fan temperature or voltage problem, or a chassis intrusion alert.

PS 1 status LED

glows green when the first power supply module in the

redundant power supply is installed and working correctly. The LED is off if
the power supply module fails or if the power supply module is not installed.

PS 2 status LED

glows green when the second power supply module in the

redundant power supply is installed and working correctly. The LED is off if
the power supply module fails or if the power supply module is not installed.

System reset button

lets you reset the server if it has become nonresponsive.

Power LED

Disk activity LED

System fault LED

System reset button

Power button

PS 1 status LED

PS 2 status LED

System fault LED reset
switch

Front panel connector

Chassis intrusion detection switch

NMI button

8508088.book Page 12 Thursday, November 1, 2001 9:35 AM

«
...
18
19
20
21
22
...
»

Содержание 930 series

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 930 series

BladeCenter QS20

Бренд: IBM Страницы: 92

BladeCenter JS20

Бренд: IBM Страницы: 218

HS21 - BladeCenter - 8853

Бренд: IBM Страницы: 80

8835 - Eserver 325 - 1 GB RAM

Бренд: IBM Страницы: 62

8835 - Eserver 325 - 1 GB RAM

Бренд: IBM Страницы: 2

8676 - Eserver xSeries 335

Бренд: IBM Страницы: 92

8670 - Eserver xSeries 345

Бренд: IBM Страницы: 60

8647 - Eserver xSeries 225

Бренд: IBM Страницы: 182

8480 - Eserver xSeries 205

Бренд: IBM Страницы: 64

Бренд: IBM Страницы: 2

Бренд: IBM Страницы: 136

Бренд: IBM Страницы: 480

Бренд: IBM Страницы: 68

@Server pSeries 630 6C4

Бренд: IBM Страницы: 180

eServer 380 xSeries

Бренд: IBM Страницы: 54

Бренд: Aastra Страницы: 502

NPort W2150Plus Series

Бренд: Moxa Technologies Страницы: 167

SUPERSERVER 5019S-M

Бренд: Supermicro Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды