Gates Power Crimp 707, Инструкция по безопасности и эксплуатации

Страница: 4 / 20

23 Die sets are available for crimping hydraulic and industrial hose from
3
⁄
16
” through 1
1
⁄
4
” I.D. A Swager Kit (Prod. No. 7480-0040, Part No. 78081)
also is available to swage thermoplastic and C14 Teflon hoses.
PC707 8-Finger Die Sets Available
Product Part
Description Number Number Notes
Die Set 721 7482-1217 78943
Die Set 722 7482-1218 78944
Die Set 731 7482-0931 78931
Die Set 732 7482-0932 78932
Die Set 733 7482-0933 78933
Die Set 734 7482-0934 78934
Die Set 735 7482-0935 78935
Die Set 736 7482-0936 78936
Die Set 737 7482-0937 78937
Die Set 739 7482-0939 78939 Must use the No-Notch Die Cone (Prod. No. 7482-0297, Part No. 78747)
Die Set 740 7482-0947 78950 For crimping 6ACA
Die Set 741 7482-0941 74951 For crimping 8ACA
Die Set 742 7482-0942 78952 For crimping 10ACA
Die Set 743 7482-0943 78953 For crimping 12ACA
Die Set 744 7482-0944 78954 For crimping power steering
Die Set 745 7482-0945 78955 For crimping grease fitting
Die Set 746 7482-0946 78956 For crimping miscellaneous (Replaces B die)
Die Set 781 7482-1231 78578 For GL Fittings
Die Set 782 7482-1232 78579 For GL Fittings
Die Set 783 7482-1233 78580 For GL Fittings
Die Set 7C3 7482-1122 78941 For crimping clamp collar (
5
⁄
8
”)
Die Set 7C4 7482-1123 78942 For crimping clamp collar (
3
⁄
4
”)
2
Specifications
Prod. No.:
7480-0043*
Part No.:
77700*
Dimensions: 13” wide x 12” deep x 26-1/2” high
Weight: 188 lbs.
Production Rate: 50 assemblies per hour (1/2” I.D. 2-wire
straight thread assemblies)
* Power Crimp 707 crimper can also be ordered wired for 230 volts (Prod. No. 7480-0046,
Part No 77701). Must be used with 230 volt power unit (Prod No. 7481-0028, Part No. 77811).
Power Crimp
®
707 Crimper
Prod. No.:
7481-0023
Part No.:
77810
Power Source: 115 Volt, 15 Amp.,
1 H.P., 60 Cycles
Dimensions: 12 “ wide x 25” deep x 12” high
Weight: 70 lbs.
Maximum Rated Working Pressure: 4900 psi.
Prod. No.: 7481-0028* Part No.: 77811*
Power Source: 230 Volt, 7.5 Amp.,
1 H.P., 60 Cycles
* Use only with Power Crimp 707 (Product No. 7480-0046,
Part No. 77701), or 230 Volt rewired Power Crimp 707 crimper only.
Electro Power Pump
Note: Do Not operate 115V crimper with a 230V pump. Digital readout will be damaged. See page 11
for additional instructions.
Do not use 720 or 739 die set with notched die cone. May cause damage to die cone.
CAUTION: