GasTech F-GUARD IR3-HD Скачать руководство пользователя страница 43

Страница: 43 / 45

For more information & technical support: [email protected]

76-M-6010-02-02

F-Guard IR3 HD User Manual

12 Warranty

GASTECH AUSTRALIA PTY LTD

agrees to extend to Purchaser/Distributor a warranty on the

GASTECH AUSTRALIA PTY LTD

. supplied components of the F-Guard products.

GASTECH

AUSTRALIA PTY LTD

. warrants to

Purchaser/Distributor that the products are free from defects in materials and workmanship for

five (5) years, commencing with the date of delivery to Purchaser/Distributor.

GASTECH

AUSTRALIA PTY LTD

. expressly excludes damage incurred in transit from the

factory or other

damage due to abuse, misuse, improper installation, lack of maintenance or

“Act of God” which are above and beyond its control.

GASTECH AUSTRALIA PTY LTD

will,

upon receipt of any defective product, transportation prepaid, repair

or replace it at its sole

discretion if found to have been defective when shipped. Said repair or

replacement is

GASTECH AUSTRALIA PTY LTD

sole liability under this

warranty and

GASTECH AUSTRALIA

PTY LTD

liability shall be limited to repair

or replacement of the component found defective and

shall not include any liability for

consequential or other damages. The customer is responsible

for all freight charges and taxes

due on shipments both ways. This warranty is exclusive of all

other warranties express or

implied.

Содержание F-GUARD IR3-HD














































Результаты поиска

Содержание F-GUARD IR3-HD

Отзывы:

Похожие инструкции для F-GUARD IR3-HD

Бренды по названию

Популярные бренды

GasTech F-GUARD IR3-HD, Руководство пользователя

Результаты поиска

Содержание F-GUARD IR3-HD

Отзывы:

Похожие инструкции для F-GUARD IR3-HD

Бренды по названию

Популярные бренды