GAS GAS MC 450F 2022 Скачать руководство пользователя страница 41

Страница: 41 / 157

TUNING THE CHASSIS 10

10.5

Adjusting the high-speed compression damping of the shock absorber

Caution

Risk of injury

Parts of the shock absorber will move around if the shock absorber is detached incorrectly.

The shock absorber is filled with highly compressed nitrogen.

–

Please follow the description provided. (Your authorized GASGAS Motorcycles workshop will be glad to help.)

Info

The effect of the high speed compression adjuster can be seen in the fast compression of the shock absorber.

F01840-11

–

Turn adjusting screw

all the way clockwise with a socket wrench.

Info

Do not loosen fitting

–

Turn counterclockwise by the number of turns corresponding to the
shock absorber type.
Guideline

Highspeed compression damping (MC 450F)

Comfort

2 turns

Standard

1.5 turns

Sport

1 turn

Highspeed compression damping (MC 450F TROY LEE DESIGNS)

Comfort

2.5 turns

Standard

2 turns

Sport

1.5 turns

Highspeed compression damping (EX)

Comfort

2.5 turns

Standard

2 turns

Sport

1.5 turns

Info

Turn clockwise to increase damping; turn counterclockwise
to reduce damping.

10.6

Adjusting the rebound damping of the shock absorber

Caution

Risk of injury

Parts of the shock absorber will move around if the shock absorber is detached incorrectly.

The shock absorber is filled with highly compressed nitrogen.

–

Please follow the description provided. (Your authorized GASGAS Motorcycles workshop will be glad to help.)

Содержание MC 450F 2022






























































































































































Результаты поиска

Содержание MC 450F 2022

Отзывы:

Бренды по названию

Популярные бренды

GAS GAS MC 450F 2022, Руководство пользователя

Результаты поиска

Содержание MC 450F 2022

Отзывы:

Бренды по названию

Популярные бренды