GAS GAS MC 350F 2022 Скачать руководство пользователя страница 26

Страница: 26 / 143

7 PREPARING FOR USE

7.7

Preparing the vehicle for rides on wet and muddy circuits

102137-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Observe the fitting instructions for

GASGAS Techni-

cal Accessories

600868-01

–

Mount the steel sprocket.

–

Clean the motorcycle. (

p. 113)

–

Straighten the bent radiator fins carefully.

7.8

Preparing vehicle for high temperatures or slow riding

600868-01

–

Adjust the secondary drive to the road conditions.

Info

The engine oil heats up quickly when the clutch is operated
frequently due to an excessively high secondary ratio.

–

Clean the chain.

Chain cleaner (

p. 132)

–

Clean the radiator fins.

–

Straighten bent radiator fins carefully.

–

Check the coolant level. (

p. 99)

7.9

Preparing the vehicle for low temperatures or snow

102137-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Observe the fitting instructions for

GASGAS Techni-

cal Accessories

Содержание MC 350F 2022
















































































































































Результаты поиска

Содержание MC 350F 2022

Отзывы:

GAS GAS MC 350F 2022, Руководство пользователя, Страница: 26 / 143

Результаты поиска

Содержание MC 350F 2022

Отзывы: