GAS GAS MC 350F 2022 страница 16 Скачать руководство пользователя

Страница: 16 / 143

6 CONTROLS

6.1

Clutch lever

A00795-10

The clutch lever

is fitted on the left side of the handlebar.

The clutch is hydraulically operated and self-adjusting.

6.2

Hand brake lever

A00798-10

Hand brake lever

is fitted on the right side of the handlebar.

The front brake is engaged using the hand brake lever.

6.3

Throttle grip

A00759-10

The throttle grip

is fitted on the right side of the handlebar.

6.4

Stop button

A00796-10

The stop button

is fitted on the left side of the handlebar.

Possible states

• The stop button

is in the basic position

–

In this position, the

ignition circuit is closed and the engine can be started.

• Stop button

pressed

–

In this position, the ignition circuit is inter-

rupted, a running engine stops, and a non-running engine will not
start.

Содержание MC 350F 2022
















































































































































Результаты поиска

Содержание MC 350F 2022

Отзывы:

Похожие инструкции для MC 350F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 350F 2022, Руководство пользователя

Результаты поиска

Содержание MC 350F 2022

Отзывы:

Похожие инструкции для MC 350F 2022

Бренды по названию

Популярные бренды