GAS GAS MC 250F 2022 Скачать руководство пользователя

Страница: 74 / 143

11 SERVICE WORK ON THE CHASSIS

A00792-10

–

Check that the chain guide is firmly seated.
» If the chain guide is loose:

–

Tighten the screws on the chain guide.
Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 44)

11.38

Checking the frame

S02306-01

–

Check the frame for damage, cracks, and deformation.
» If the frame shows signs of damage, cracks, or deformation:

–

Change the frame.
Guideline

Repairs on the frame are not permitted.

11.39

Checking the link fork

S02305-01

–

Check the link fork for damage, cracks, and deformation.
» If the link fork shows signs of damage, cracks, or deformation:

–

Change the link fork.

Info

Always replace a damaged link fork. GASGAS Motor-
cycles does not permit repairing link forks.

11.40

Checking the throttle cable routing

Preparatory work

–

Remove the seat. (

p. 56)

–

Remove the fuel tank.

(

p. 63)

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды