GAS GAS MC 250F 2022 Скачать руководство пользователя

Страница: 58 / 143

11 SERVICE WORK ON THE CHASSIS

A00818-10

–

Position the angle lever and linkage lever.

–

Mount and tighten fitting

Guideline

Nut, linkage lever on
angle lever

M14x1.5

60 Nm (44.3 lbf ft)

Info

Pay attention to flat area

–

Mount and tighten screw

Guideline

Screw, bottom
shock absorber

M10

60 Nm (44.3 lbf ft)

Loctite

2701™

Info

Raise the link fork slightly to be able to mount the screw
more easily.

A00809-11

–

Attach the frame protector in area

and position it.

–

Mount and tighten screws

with the washers.

Guideline

Screw, frame protector M5

3 Nm (2.2 lbf ft)

–

Mount the new cable ties.

Finishing work

–

Check the free travel of the foot brake lever. (

p. 82)

–

Remove the motorcycle from the lift stand. (

p. 44)

11.20

Removing the seat

Caution

Danger of burns

The voltage regulator gets very hot when the vehicle is driven.

–

Allow the voltage regulator to cool down before performing any work.

A00781-10

–

Remove screw

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды