GAS GAS MC 250F 2022 Скачать руководство пользователя

Страница: 57 / 143

SERVICE WORK ON THE CHASSIS 11

A00814-10

–

Hold the shock absorber and remove screw

–

Remove the shock absorber carefully at the bottom.

11.19

Installing the shock absorber

A00815-10

Main work

–

Carefully position the shock absorber into the vehicle from the bot-
tom.

–

Mount and tighten screw

Guideline

Screw, top shock
absorber

M10

60 Nm (44.3 lbf ft)

Loctite

2701™

A00816-10

–

Position the link fork and mount the swingarm pivot.

Info

Pay attention to flat area

–

Mount and tighten nut

Guideline

Nut, fork pivot

M16x1.5

100 Nm (73.8 lbf ft)

A00812-10

–

Mount the chain.

–

Connect the chain with connecting link

Guideline

The closed side of the chain joint lock must face in the direction
of travel.

A00817-10

–

Position the foot brake cylinder.

Push rod

engages in the foot brake cylinder.

Info

Ensure that the dust boot is correctly seated.

–

Mount and tighten screws

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды