GAS GAS MC 250F 2022 страница 126 Скачать руководство пользователя

Страница: 126 / 143

22 TECHNICAL DATA

124

22.3

Capacities

22.3.1

Engine oil

Engine oil

1.0 l (1.1 qt.)

Engine oil (SAE 10W/50) (

p. 130)

22.3.2

Coolant

Coolant

0.95 l (1 qt.)

Coolant (

p. 130)

22.3.3

Fuel

Total fuel tank capacity, approx. (MC)
Super unleaded (ROZ 95) (

p. 131)

7 l (1.8 US gal)

Total fuel tank capacity, approx. (EX)
Super unleaded (ROZ 95) (

p. 131)

8.5 l (2.25 US gal)

Fuel reserve, approx. (EX)

1.5 l (1.6 qt.)

22.4

Chassis

Frame

Central tube frame made of chrome molybdenum steel
tubing

Fork

WP XACT AER

Suspension travel

front

310 mm (12.2 in)

rear

300 mm (11.81 in)

Fork offset

22 mm (0.87 in)

Shock absorber

WP XACT 5750

Brake system

Disc brakes, floating brake calipers

Brake discs - diameter

front

260 mm (10.24 in)

rear

220 mm (8.66 in)

Brake discs - wear limit

front

2.5 mm (0.098 in)

rear

3.5 mm (0.138 in)

Offroad tire pressure

front

1.0 bar (15 psi)

rear

1.0 bar (15 psi)

Secondary ratio (MC)

14:51

Secondary ratio (EX)

13:51

Chain

5/8 x 1/4"

Available rear sprockets

48, 50, 51, 52

Steering head angle

63.9°

Wheelbase

1,485 ± 10 mm (58.46 ± 0.39 in)

Seat height, unloaded

950 mm (37.4 in)

Ground clearance, unloaded

370 mm (14.57 in)

Weight without fuel, approx. (MC)

99 kg (218 lb.)

Weight without fuel, approx. (EX)

100 kg (220 lb.)

Maximum permissible front axle load

145 kg (320 lb.)

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды