GARO GBO-300 Скачать руководство пользователя

Страница: 26 / 63

Universal dimmer actuators GDA2K-400 KNX / GDA4K-400 KNX

pdated: Mai-17 (Subject to changes) Page 26 of 63

Continuation:

Designation

Values

Description

Load selection

(continuation)

dimmable energy-saving lamps

with L response

With ESL, only use if a
disruptive flickering is noted
when dimming up or down.
See appendix: Dimming energy-
saving lamps (ESL)

Fan (soft switching deactivated)

Special mode for fans, with
configurable start-up time (see
below).

LEDs (RC, 0-90%)

Only for LED lights that cannot
be dimmed at 100%.

Reserve 2

…

Reserve 32

Do not use.

Start-up time

2-60 s

Only with

Load selection

fan

Time for which the fan must be
driven with full voltage, until it
has reached a specific speed.

Minimum dimming value

1%, 5%, 10%,

15%, 20%, 25%, 30%
35%, 40%, 45%, 50%

Minimum dimming value for all
dimming processes (except 0%).
Any values (switch-on dimming
value, response to bus failure,
etc.) which are below this
threshold are increased to the
minimum dimming value.

Dimming time 1 from 0% to
100%

1 s, 2 s, 4 s

6 s, 8 s, 12 s,

15 s, 24 s, 30 s, 60 s

This parameter defines the
maximum dimming speed from
0 to 100%
For greater flexibility 3 different
values can be specified.
(see below).

Dimming time 2 from 0% to
100%

1 s, 2 s, 4 s

6 s, 8 s, 12 s,

15 s, 24 s, 30 s, 60 s

Dimming time 3 from 0% to
100%

1 s, 2 s, 4 s

6 s, 8 s, 12 s,

15 s, 24 s, 30 s, 60 s

Behaviour when receiving a
switch command (1-bit)

immediate on

The change from 0% to 100% or
100% to 0% takes place within
max. 1 s.

soft on with dimming time 1

soft on with dimming time 2
soft on with dimming time 3

The change from 0% to 100% or
100% to 0% takes place within
the preset dimming time.

Содержание GBO-300
































































Результаты поиска

Содержание GBO-300

Отзывы:

Похожие инструкции для GBO-300

Бренды по названию

Популярные бренды

GARO GBO-300, Руководство пользователя

Результаты поиска

Содержание GBO-300

Отзывы:

Похожие инструкции для GBO-300

Бренды по названию

Популярные бренды