Using the Light
You can use the light feature on your device to verify pairing,
help locate your dog, and provide safety for your dog at night.
1
Select a dog collar device (
).
2
Move the mode toggle switch to
A
.
3
Select the top training key to turn the light on.
4
Select the bottom training key to turn the light off.
Beeper Device
The Pro 550 system works with optional accessories, including
a beeper device. The beeper device emits high-volume sounds
to provide information about the location and status of your
dogs. You can operate the beeper device remotely using the
Pro 550 system. For more information or to purchase
accessories, go to
.
Device Information
Pro 550 Handheld Device Specifications
Battery type
Rechargeable, replaceable lithium-
ion
Battery life
60 hours typical use
Operating temperature range
From -4° to 140°F (from -20° to
60°C)
Charging temperature range
From 32° to 104°F (from 0° to
40°C)
Storage temperature range (less
than 1 month)
From -4° to 122°F (from -20° to
50°C)
Storage temperature range (less
than 3 months)
From -4° to 104°F (from -20° to
40°C)
Storage temperature range (less
than 1 year)
From -4° to 68°F (from -20° to
20°C)
Water rating
IEC 60529 IPX7*
Wireless range
1 mi. (1.6 km)
*The device withstands incidental exposure to water of up to
1 meter for up to 30 minutes.
Pro 550 Dog Collar Device Specifications
Battery type
Rechargeable, replaceable lithium-ion
Battery life
60 hours typical use
Operating temperature range
From -4° to 140°F (from -20° to 60°C)
Charging temperature range
From 32° to 104°F (from 0° to 40°C)
Storage temperature range (up
to 1 month)
From -4° to 122°F (from -20° to 50°C)
Storage temperature range (up
to 3 months)
From -4° to 95°F (from -20° to 35°C)
Water rating
1 ATM*
*The device withstands pressure equivalent to a depth of
10 meters.
Checking the Battery Level
Turn on the dog collar device (
).
The status LED flashes every few seconds while the device is
on. The color of the status LED indicates the battery charge
level.
Green
The battery has a good charge.
Yellow
The battery should be charged soon.
Red
The battery is very low and should be charged
immediately.
Flashing Red The battery is depleted and must be charged. Training
features are disabled.
Pro 550 Battery Replacement Instructions
WARNING
This product contains a lithium-ion battery. To prevent the
possibility of personal injury or product damage caused by
battery exposure to extreme heat, store the device out of direct
sunlight.
Do not use a sharp object to remove batteries.
CAUTION
Contact your local waste disposal department to properly
recycle the batteries.
Pro 550 Handheld Device Components
À
Security screws
Á
Back plate
Â
Battery plate screws
Ã
Gasket
Ä
Battery plate
Å
Battery
Replacing the Pro 550 Handheld Device Battery
Before you replace the battery, you must remove all dirt, water,
and debris from the device. You also need a small Phillips
screwdriver and the security screwdriver included with the
battery replacement kit.
You can purchase a replacement battery at
. You should use only an official Garmin®
replacement part.
1
Remove the eight security screws from the back of the
device.
2
Lift up the back plate.
3
Grip the battery connector wires close to the connector, and
pull the connector perpendicular to the circuit board to
disconnect the battery connector from the device.
4
Grip the rotary switch connector wires close to the connector,
and pull the connector perpendicular to the circuit board to
disconnect the rotary switch connector from the device.
5
Remove the two screws from the battery plate.
6
Lift up the battery plate.
7
Remove the old battery from the back plate, noting the
orientation of the battery.
The battery fits tightly. It may be necessary to pry the battery
out of the back plate using a non-sharp, non-metal object.
4
Device Information
