background image

190-00133-02 Rev B

                                                                                                                                                                    

      i

TABLE OF CONTENTS

SECTION 1

DESCRIPTION AND OPERATION

PARAGRAPH

PAGE

1.1 INTRODUCTION ............................................................................................................... 1-1

1.2 GENERAL DESCRIPTION ................................................................................................ 1-1

1.3 TECHNICAL SPECIFICATIONS ........................................................................................ 1-1

1-4 EQUIPMENT DESCRIPTION ............................................................................................ 1-2

1-5 SCOPE OF MAINTENANCE ............................................................................................. 1-3

SECTION 2

SPECIAL TEST EQUIPMENT

2.1 INTRODUCTION ............................................................................................................... 2-1

2.2 SPECIAL TOOLS AND TEST EQUIPMENT ...................................................................... 2-1

SECTION 3

ALIGNMENT AND TESTING

3.1 INTRODUCTION ............................................................................................................... 3-1

3.2 ALIGNMENT ...................................................................................................................... 3-1

3.3 TESTING ........................................................................................................................... 3-5

SECTION 4

DISASSEMBLY AND REASSEMBLY

4.1 INTRODUCTION ............................................................................................................... 4-1

4.2 INSPECTION ..................................................................................................................... 4-1

4.3 FRONT SUBASSEMBLY ................................................................................................... 4-1

4.4 CLEANING ........................................................................................................................ 4-2

Содержание GTX 320 ATC

























Отзывы: