Garmin GPSMAP 546 Скачать руководство пользователя страница 10

Страница: 10 / 78

Device Overview

GPSMAP 400/500 Series Owner’s Manual

Adjusting the Backlight

1. Press and release the

Power

key.

2. Press left or right on the

Rocker

to adjust the brightness.

NOTE:

Press the Power key repeatedly to cycle between maximum

backlight, minimum backlight, and your manual setting.

To allow the unit to automatically adjust the backlight based on ambient light,

select

auto backlight

(automatic backlight is available only on the GPSMAP

536 and 546).

To switch between Day and night mode:

1. Press and release the

Power

key.

2. Select

Color Mode

3. Press left or right on the

Rocker

to switch between modes.

To allow the unit to automatically adjust the backlight based on ambient light,

select

auto day/Night Mode

Содержание GPSMAP 546















































































Результаты поиска

Содержание GPSMAP 546

Отзывы:

Похожие инструкции для GPSMAP 546

Бренды по названию

Популярные бренды

Garmin GPSMAP 546, Руководство пользователя

Результаты поиска

Содержание GPSMAP 546

Отзывы:

Похожие инструкции для GPSMAP 546

Бренды по названию

Популярные бренды