background image

190-01134-11

GMA 350/350c/350H/350Hc Installation Manual

Rev. J

Page A-3

J2-13

ICS Mute Inhibit*

J3502-13

MARKER HI SENS* IN

If previous GMA 340 wiring connected 
this input to ground, default GMA 350/
350H configuration will result in 
Marker Beacon RX mode always in HI 
SENS.

If previous wiring connected this input 
only to J3502-14, there is no compati-
bility issue

Option 1: Remove previous wiring or 
connect to a switch to ground to allow 
for pilot selectable MKR SENS mode.
Option 2: Using the GMA 350/350H 
configuration tool, configure the 
J3502-13 input for no function instead 
of MKR HI SENS.
NOTE: The feature to mute music 
during ICS is still available with the 
configuration tool.

J2-14

ICS Mute Inhibit Return

J3502-14

PASS ISO TOGGLE/ICS KEY* IN

If previous GMA 340 wiring connected 
this input to ground, default GMA 350/
350H configuration will result in PASS 
ICS state toggled each power-up.

If previous wiring connected this input 
only to J3502-13, there is no compati-
bility issue.

Option 1: Remove previous wiring or 
connect to a pushbutton to ground 
allow passengers to toggle ICS state 
or configure as PASS ICS key.
Option 2: Using the GMA 350/350H 
configuration tool, configure the 
J3502-14 input for no function instead 
of PASS ISO TOGGLE/ICS KEY* IN.
NOTE: The feature to mute music 
during ICS is still available with the 
configuration tool.

J2-15

High Music Gain Select*

J3502-15

ALERT 2 AUDIO IN HI

None if not desired to use ALERT 2 
AUDIO IN source. 

None.
NOTE: GMA 350/350H music gain is 
both configurable and pilot 
adjustable. If the pilot adjustment 
range does not yield desired volumes, 
configuration offset can be adjusted 
as desired.

J2-17

8 Ohm Select*

J3502-17

RS-232 IN

If previous GMA 340 wiring connected 
this input to ground, there will be no 
damage or effect in GMA 350/350H 
operation.

None if RS-232 communication to 
other Garmin equipment is not 
needed. Otherwise, remove old wir-
ing and connect RS-232 port to as 
documented in system install 
instructions.

J2-18

Reserved

J3502-18

RS-232 OUT

None

None

J2-19

Tone Enable*

J3502-19

PA MODE SELECTED* OUT

If previous GMA 340 wiring connected 
this pin to ground, there will be no 
damage or effect in GMA 350/350H 
operation.

None unless new PA MODE 
SELECTED* OUT function is desired 
for wiring interface to other 
equipment.

J2-21

Swap Return

J3502-21

RESERVED

If previous GMA 340 wiring used this 
pin as the return path for the J2-20 
Swap input, the default GMA 350/
350H configuration will continue to 
support this function without a wiring 
change.

None

J2-22

NC

J3502-22

PLAY KEY* IN

None

None

Table A-1.  GMA 340/GMA 350 Pin Differences

GMA 340 

Connector/

Pin Number

GMA 340 

Pin Function

GMA 350/350H

Connector/Pin 

Number

GMA 350/350H

Pin Function

Possible GMA 340 Wiring 

Compatibility Issues

Corrective Action

Содержание GMA 350

































































Отзывы: