Garmin GDL 82 Скачать руководство пользователя страница 63

Страница: 63 / 68

System Checkout

190-01810-00

GDL 82 TSO Installation Manual

Rev. 5

Page 8-4

Discrete Output

If the GDL 82 is connected to any optional external annunciators, perform the following steps:

Go to the GDL 82 Discretes page.

If the Fault Alert discrete output is connected to an annunciator, toggle the output to ACTIVE (corresponding box

is checked and displays “ACTIVE”) and verify that the annunciator is illuminated. Toggle the Fault Alert output to
INACTIVE (corresponding box is not checked and displays “INACTIVE”), and verify the annunciator is
extinguished.

If the annunciator does not receive the signal, verify the wiring and ensure it is connected properly and not

shorted to ground.

8.2 Documentation Checks

8.2.1 Flight Manual Supplement

If the installation needs an FMS, sample versions can be found at

flyGarmin.com

Содержание GDL 82





































































Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды

Garmin GDL 82, Руководство по установке

Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды