Garmin GDL 82 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 68

background image

Connector Pinouts

190-01810-00

GDL 82 TSO Installation Manual

Rev. 5

Page 5-3

Discrete Inputs*

The GDL 82 has two active-low discrete input pins denoted with an asterisk (*). The following signal conditions are
required for the states of those inputs:

•

Active (low) state: Input signal is < 1.0 VDC and/or resistance to ground < 375

ohm

•

Inactive (open/high) state: Input signal is between 2.0 VDC and 33 VDC and/or resistance to ground > 130 kilohm

5.2 Functional Descriptions

5.2.1 Power and Antennas

This section provides power input requirements and antenna connections. Refer to section 10 for interconnect
information. The transponder and antenna connections use BNC coaxial connectors. The GPS/SBAS antenna uses a
TNC coaxial connector.

Table 5-2 Power

Table 5-3 Antennas

PIN NAME

CONNECTOR

PIN

I/O

POWER

P821

15

In

GROUND

P821

14

--

P821

7

--

PORT NAME

CONNECTOR

TRANSPONDER

XPDR

L-BAND ANTENNA

ANT

GPS/SBAS ANTENNA

GPS

«
...
33
34
35
36
37
...
»

Содержание GDL 82





































































Отзывы:

Нет отзывов

Похожие инструкции для GDL 82

AquaTrans AT868

Бренд: GE Страницы: 67

Бренд: Offshore Страницы: 14

Бренд: Uniden Страницы: 17

Бренд: EastLink Страницы: 3

Бренд: Sandstrom Страницы: 36

Бренд: Kathrein Страницы: 64

Бренд: dikom Страницы: 21

Бренд: FUTABA Страницы: 22

Бренд: Samson Страницы: 15

Бренд: Tivoli Audio Страницы: 6

Бренд: Harman Kardon Страницы: 28

Бренд: GE Страницы: 40

Бренд: Teac Страницы: 20

Бренд: Immersion Страницы: 5

Бренд: Dolphin Страницы: 17

Бренд: IDS Страницы: 2

Бренд: Yaesu Страницы: 32

Бренд: Patton electronics Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды