background image

Fusion

®

 BB100 Black Box Entertainment System with Wired Remote 

Control Installation Instructions

Important Safety Information

 WARNING

Failure to follow these warnings and cautions could result in personal injury, damage to the vessel, or poor 
product performance.
See the Important Safety and Product Information guide in the product box for product warnings and other 
important information.
This device must be installed according to these instructions.
Disconnect the vessel's power supply before beginning to install this product.
Before applying power to this product, make sure it has been correctly grounded, following the instructions in 
the guide.

 CAUTION

To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling, 
cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel.

You must read all installation instructions before beginning the installation. If you experience difficulty during 
the installation, contact Fusion Product Support.

Software Updates

For best results, you should update the software in all Fusion devices at the time of installation to ensure 
compatibility.
You can update the software using a USB flash drive. For software updates and instructions on updating the 
device using the USB flash drive, go to the device product page at 

support.garmin.com

.

Tools Needed

• Phillips screwdriver
• Electric drill
• Drill bit (size varies based on surface material and screws used)
• Rotary cutting tool or jigsaw
• Silicone-based marine sealant (optional)

GUID-CA5786C5-2DDE-4E40-90C4-FDF4A021C759 v5

April 2022

Содержание Fusion BB100













Отзывы: