Garland XG24-JIB Скачать руководство пользователя страница 1

Страница: 1 / 88

Part # JIBSM08 Rev.6 (08/04/09)

Page 1

GARLAND COMMERCIAL INDUSTRIES, LLC

185 East South Street

Freeland, Pennsylvania 18224

Phone: (570) 636-1000

Fax: (570) 636-3903

GARLAND COMMERCIAL RANGES, LTD.

1177 Kamato Road, Mississauga, Ontario L4W 1X4

CANADA

Phone: 905-624-0260

Fax: 905-624-5669

Part #JIBSM08 Rev 7 (08/04/09)

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE

OR OTHER FLAMMABLE VAPORS OR

LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER

APPLIANCE

WARNING:

IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR MAINTENANCE CAN

CAUSE PROPERTY DAMAGE, INJURY, OR DEATH.

READ THE INSTALLATION,

OPERATING AND MAINTENANCE

INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR

SERVICING THIS EQUIPMENT

NOTE:

THIS MANUAL PERTAINS TO ALL XPRESS GRILL

MODELS LISTED ABOVE. THE READER/OPERATOR

MUST INTERPRET ITS CONTENTS TO APPLICABLE

NEEDS. HOWEVER, IF THERE IS ANY QUESTION OF

INTERPRETATION OF ANY LITERATURE PERTAINING

TO GARLAND GRILLS, PLEASE CONTACT OUR

CUSTOMER SERVICE DEPARTMENT AT ONE OF THE

PHONE NUMBERS LISTED BELOW.

PLEASE READ ALL SECTIONS OF THIS MANUAL AND

RETAIN FOR FUTURE REFERENCE.

THIS PRODUCT HAS BEEN CERTIFIED AS COMMERCIAL

COOKING EQUIPMENT AND MUST BE INSTALLED BY

PROFESSIONAL PERSONNEL AS SPECIFIED.

CAUTION: THIS EQUIPMENT MUST ONLY BE OPERATED

UNDER AN APPROVED HOOD SYSTEM

IN THE COMMONWEALTH OF MASSACHUSETTS

THIS PRODUCT MUST BE INSTALLED BY A LICENSED

PLUMBER OR GAS FITTER.

For Your Safety:

Post in a prominent location, instructions to be

followed in the event the user smells gas. This

information shall be obtained by consulting your local

gas supplier.

SERVICE MANUAL

JACK IN THE BOX

GAS XPRESS GRILLS,

MODELS XG24-JIB, XG36-JIB

MODEL NUMBERS:

XG24-JIB,XG36-JIB

Содержание XG24-JIB

























































































Результаты поиска

Содержание XG24-JIB

Отзывы:

Бренды по названию

Популярные бренды

Garland XG24-JIB, Руководство по обслуживанию

Результаты поиска

Содержание XG24-JIB

Отзывы:

Бренды по названию

Популярные бренды