background image

48 

Part Number  4532415   Rev 5  12/15

OPERATION SAFETY—DISCLAIMER

 DANGER

The on-site supervisor is responsible for ensuring that 

operators are made aware of the inherent dangers of 

operating this equipment.

 DANGER

Risk of fire/shock/equipment failure. All minimum 

clearances must be maintained. Do not obstruct 

vents or openings.

n

Warning

This equipment is intended for indoor use only.  Do not 

install or operate this equipment in outdoor areas.

Notice

The reliability of the appliance can only be guaranteed 

when it is used properly. The appliance must always 

be operated within the limits and/or the operating 

conditions provided in this manual. 

Notice

Avoid dropping any hard objects onto the equipment. 

Damages to the heating surface will shortened the life 

cycle of the equipment or incur high service costs.

Notice

—Models with Glass-Top

Use Only Induction Suitable Cookware

Use only induction suitable cookware with proper sizes 

and made of proper material. The induction suitable 

cookware must be in good condition without any 

uneven, arched or partially detached bottoms.
Using unsuitable cookware can cause the appliance 

to fail prematurely, void your warranty, or incur high 

service costs. 

Notice

—Induction Griddles / Braising Pans

NEVER heat any cooking pan on the griddle plate or 

in the braising pan. Heating cooking pan with these 

equipment will damage these equipment. Heat only 

food products on the griddle plate or in the braising pan.

OPERATION SAFETY—PERSONAL PROTECTION

Notice

Induction appliances are more powerful, heat up 

pans quicker, and cook food faster than conventional 

cooking equipment. Your induction appliance will 

require different use and care than other conventional 

equipment.
Do not operate the equipment without reading this 

manual and understanding all safety requirements.

 DANGER

If any part of the appliance is cracked or broken, Stop 

and Immediately Turn Off the appliance. Only if it 

is possible and safe, disconnect the equipment from 

main power supply. Do not touch any parts inside the 

appliance. 
Disconnect electric power at the main power disconnect 

for all equipment being serviced. 
Failure to disconnect the power at the main power 

supply disconnect could result in serious injury or death. 

The power switch DOES NOT disconnect all incoming 

power.
Contact an authorized service agency for assistance.

 DANGER

Do not operate any appliance with a damaged or 

pinched cord or a damaged plug. All repairs must be 

performed by a qualified service company.

 DANGER

Keep power cord AWAY from HEATED surfaces. DO NOT 

immerse power cord or plug in water. DO NOT let power 

cord hang over edge of table or counter.

 DANGER

To avoid cardiac pacemaker malfunction, consult your 

physician or pacemaker manufacture about effects of 

electromagnetic field on your pacemaker.

 DANGER

Never stand, site, or lean on the equipment! They are 

not designed to hold the weight of an adult, and may 

collapse or tip if misused in this manner.

Section 3

Operation

Содержание GI-MO/DU 7000

































































Отзывы: