manualshive.com logo in svg

Gardner Denver Welch LVS 105 T 10 ef+, Руководство по эксплуатации, Страница: 42 / 64

Поделиться
Скачать
Gardner Denver Welch LVS 105 T 10 ef+ Скачать руководство пользователя страница 42

Operation 

42 

Operation Manual LVS 105 T 

– 10 ef

+

 

 

Display log files 

1.  Select the "System settings" menu option.  

2.  Select the "Log files" menu option. 

3.  Select the "Display log files" menu option. 

4.  Select a log file. 

5.  Confirm your entry. 

Delete log files 

1.  Select the "System settings" menu option. 

2.  Select the "Log files" menu option. 

3.  Select the "Display log files" menu option. 

4.  Press the rotary encoder for 2 s. 

5.  You will see "Do you really want to delete log files?" 

6.  Confirm your selection with "Yes." 

6.3.3 

Reset to factory settings 

1.  Select the "System settings" menu option. 

2.  Select the "Reset to factory settings" menu option. 

3.  Confirm your selection with "Yes." 

 

NOTE

 After selecting "Yes" (with check mark), the language is set back to the factory setting 

(English). All values are also reset to the factory settings. 

6.4  "PC-Control 601" PC software (Option) 

The 

PC-Control 601

 PC software is used for the remote control of the vacuum controller of 

the device. In general, the PC software offers the same control options as found in the end 
device. In addition, the following operations are possible with the PC software: 

  Firmware updates 

  Transfer time and date from the PC 

  Factory settings and factory calibration (not public) 

6.4.1 

Installation 

NOTE

 The PC software can be downloaded as installer package. The file "setup.exe" installs 

the PC software and the required CVI Runtime Environment. 

1.  Select the "PC-Control 601" PC software. It is available as freeware from 

www.gard-

nerdenver.com/de-de/welch 

in the "Service" menu à download area.  

2.  Call up the PC software with "VC601_XXX.exe" in the installation directory. 

NOTE

 XXX describes the sequential version number of the PC software. 

 

Содержание Welch LVS 105 T 10 ef+

































































Отзывы:

Нет отзывов