Gardena SILENO minimo Скачать руководство пользователя страница 4

The product must only be operated, maintained

and repaired by persons that are fully conversant

with its special characteristics and safety

regulations.

It is not permitted to change the initial design of the

product.

Obey national regulations about electrical safety.

GARDENA does not guarantee full compatibility

between the product and other types of

wireless systems such as remote controls, radio

transmitters or equivalent.

The built-in alarm is very loud. Be careful,

especially if the product is handled indoors.

Operation and storage temperature range is 0-50

°C / 32-122 °F. Temperature range for charging is

0-45 °C / 32-113 °F. Too high temperatures can

cause damage to the product.

1.3 Safety instructions for installation

WARNING: 

Read the warning

instructions that follow before you use the

product.

Do not install the charging station, including any

accessory, at a location that is below, or within 60

cm / 24 in. from, any combustible material. In case

of malfunction, heating of the charging station and

the power supply may occur and create a potential

risk of fire.

Do not put the power supply at a height where

there is a risk it can be put in water. Do not put the

power supply on the ground.

Do not encapsulate the power supply. Condensed

water can harm the power supply and increase the

risk of electrical shock.

Applicable to USA/Canada. If power supply is

installed outdoors: Risk of Electric Shock. Install

only to a covered Class A GFCI receptacle (RCD)

that has an enclosure that is weatherproof with the

attachment plug cap inserted or removed.

1.4 Safety instructions for operation

WARNING: 

Read the warning

instructions that follow before you use the

product.

Keep your hands and feet away from the rotating

blades. Do not put your hands or feet near or

below the product when it is set to ON.

Use the park mode or set the product to OFF when

persons, especially children or animals are in the

work area. Refer to 

Park on page 23

. GARDENA

recommends to set the product to operate when

the work area has no activity. The product can

cause injury to animals at night in work area, for

example hedgehogs. Refer to 

Park / Schedule on

page 23

.

Make sure that there are no objects such as

stones, branches, tools or toys on the lawn. The

blades can be damaged if it hits an object.

Do not lift the product or move it when it is set to

ON.

Do not to let the product collide with persons or

animals. If a person or animal comes in the way of

the product, stop the product immediately. Refer to

To stop the product on page 24

.

Do not put objects on top of the product or its

charging station.

Do not use the product if the STOP button does

not work.

Always set the product to OFF when it is not in

operation. The product can only start when you

enter the correct PIN code.

Do not use the product at the same time as a

pop-up sprinkler. Use the 

Schedule

 function so the

product and pop-up sprinkler do not operate at the

same time. Refer to 

Park / Schedule on page 23

.

1.5 Safety instructions for maintenance

WARNING: 

Read the warning

instructions that follow before you do

maintenance on the product.

Set the product to OFF when you do maintenance

on the product.

Do not use a high-pressure washer to clean the

product. Do not use solvents to clean the product.

Disconnect the plug to the charging station before

you clean or do maintenance of the charging

station.

1.6 Battery safety

WARNING: 

Read the warning

instructions that follow before you use the

product.

Lithium-ion batteries can explode or cause fire if

disassembled, short-circuited, exposed to water,

fire, or high temperatures. Handle carefully, do

not dismantle, open the battery or use any type

of electrical/mechanical abuse. Avoid storage in

direct sunlight.

4 - Safety

1585 - 007 - 26.10.2022

Содержание SILENO minimo













































Отзывы: