GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 78

background image

TR-HT2xx LED Controller - User Manual

2

Safety

Read this before using the TR-HT. Always observe the following safety
precautions. If in doubt, contact your distributor or Gardasoft Vision. The
following symbols mean:

Warning:

Read instructions to understand possible hazard

Warning:

Surface may get hot.

Warning:

Possible hazardous voltage.

Where these symbols appear in the manual, refer to the text for
precautions to be taken.

2.1

Heat

Ensure the TR-HT is mounted correctly (see

Section 5, Mounting the TR-

), and that you do not exceed any of the ratings for the unit (see

13, TR-HT reference information

).

At its maximum ratings, the TR-HT’s enclosure can exceed 65°C which is
sufficient to cause a burn if touched. Place in a position where personnel
cannot accidentally touch it and ensure there is a free flow of air around
the unit.

2.2

Electrical

The TR-HT produces high energy pulses. Take care to connect the
outputs correctly and protect the output wiring and load from any short
circuits. When switched off, energy remains stored in the TR-HT for about
2 minutes.

The TR-HT does not have complete tracking isolation of inputs (including
triggering and communications ports) and outputs, therefore, please
observe the following guidance:

Computer equipment that is connected to the communication or trigger
ports must be internally powered or separated from mains electricity by
double insulation/reinforced isolation or be approved to IEC 60950-1
standard. All other equipment connected to the triggers or other ports
must also have double insulation/reinforced isolation protection from the
mains supply.

The Power Supply Unit (PSU) used to energise the TR-HT must provide
double insulation/reinforced isolation from mains electricity and protected
against short circuits and overloads. We recommend using a PSU that
limits its output current to the appropriate rating of the controller by
design, by setting the current limit on the supply (if possible), or through

—

8

—

«
...
6
7
8
9
10
...
»

Содержание TR-HT2 Series















































































Отзывы:

Нет отзывов

Похожие инструкции для TR-HT2 Series

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 95

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 33

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

VLT AQUA Drive FC 200

Бренд: Danfoss Страницы: 91

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 100

Бренд: Danfoss Страницы: 82

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 12

OPTYMA Plus OP-LPQM

Бренд: Danfoss Страницы: 8

Бренд: Samson Страницы: 56

Бренд: EasyIO Страницы: 17

Бренд: cinetto Страницы: 56

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды