GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 72

Страница: 72 / 78

TR-HT2xx LED Controller - User Manual

13.2

Restrictions

The following timings and restrictions are applied when commands are
entered. Exceeding these values causes an error to be returned.

The keypad interface prevents invalid values being entered at the
controller.

13.2.1 Continuous mode

The maximum continuous output current for the TR-HT is 5.0A per
channel.

13.2.2 Switched mode

The maximum delay from the trigger input changing state to the output
current switching on or off is 100μs.

The maximum switched output current for the TR-HT is 50.0A per
channel.

13.2.3 Pulse mode

The maximum pulsed current for the TR-HT is 50A per channel. When
operating at high currents, even if you set a delay of 0μs, there is a delay of
approximately 4μs.

—

Содержание TR-HT2 Series















































































Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды

GARDASOFT TR-HT2 Series, Руководство пользователя

Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды