GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 78

background image

TR-HT2xx LED Controller - User Manual

12

Configuration commands

In addition to configuring the TR-HT using its web page interface, you can
configure it from the front panel or by using either of the network
connections. Both of these methods are described in this section along
with general information about setting up lights.

12.1

Lighting setup

Lighting units have a rating, given in current or voltage, that produces
100% brightness continuously. The TR-HT controller is compatible with
current or voltage rated lights.

If you connect a

triniti

enabled light, its ratings are set up by the TR-HT

automatically. Otherwise, you must enter the rating for the light before
connecting it to the controller, or if you replace it with a different type of
light.

Always consult the labelling on the lamp or the datasheet for its rating.
Where a voltage and current rating are quoted, use the voltage to set up
the controller. Where a voltage and power rating are quoted, use the
voltage rating. In all other cases use the current rating. If the light is not
rated, use the current rating from the LED datasheet.

The current rating can be set from 0.01A to 50A for the TR-HT in steps of
0.01A. The voltage rating can be set from 12V to 24V in steps of 1V.

When a voltage rated light is connected, the TR-HT automatically senses
the current rating of the light.

Both voltage and current rated lights are driven with a constant current.
This provides better brightness stability and allows the TR-HT to prevent
the light being over-driven.

12.2

Front panel commands

Using the front panel keypad, you can set the configuration, set a key lock
code so unauthorised users cannot change any settings, set the internal
trigger timer, view trigger status, and set the voltage or current rating.

12.2.1 Startup

On power-up the TR-HT displays its name, its serial number, and the
firmware version. The TR-HT then carries out a check on its channels,
sensing each of the outputs. When the check is complete, the
TR-HT displays

End

followed by the mode each channel has been set up

in. For example:

—

49

—

«
...
47
48
49
50
51
...
»

Содержание TR-HT2 Series















































































Отзывы:

Нет отзывов

Похожие инструкции для TR-HT2 Series

Бренд: S&C Страницы: 40

Бренд: GE Страницы: 425

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 42

Бренд: ZEHUS Страницы: 28

Бренд: Valfonta Страницы: 12

Бренд: rada Страницы: 16

Бренд: GCE Страницы: 24

Бренд: IAI Страницы: 5

Бренд: IDK Страницы: 96

Бренд: Ultraflex Страницы: 7

Бренд: Parker Страницы: 38

Бренд: Parker Страницы: 2

Бренд: OJ Electronics Страницы: 8

Бренд: Ascon tecnologic Страницы: 16

Бренд: KIOUR Страницы: 3

Бренд: Topway Страницы: 14

Бренд: Wave Home Solutions Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды