GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 78

background image

TR-HT2xx LED Controller - User Manual

4

Sécurité

Lisez ce document avant d'utiliser le TR-HT. Respectez les mesures de
sécurité suivantes en toutes circonstances. En cas de doute, contactez
votre distributeur ou Gardasoft Vision. Les symboles ci-dessous auront la
signification suivante:

Attention:

Lisez les instructions pour comprendre quels sont les

risques éventuels

Attention:

La surface peut devenir chaude.

Attention:

Risque d’électrocution.

Lorsque ces symboles apparaissent dans le manuel, reportez-vous aux
consignes pour connaître les précautions à prendre.

4.1

Chaleur

Veillez à ce que le TR-HT soit monté correctement (voir

Mounting the TR-HT

) et à ne dépasser aucune valeur nominale pour l'unité

(voir

Section 13, TR-HT reference information

).

Lorsqu'il atteint ses valeurs nominales maximales, le boitier TR-HT peut
dépasser les 65°C, ce qui est suffisant pour provoquer des brûlures en cas
de contact. Placez l'appareil à un endroit où le personnel ne risque pas de
le toucher par accident et veillez à ce que l'air circule librement autour de
l'unité.

4.2

Électricité

Le TR-HT produit des impulsions d'énergie élevées. Veillez à bien
raccorder les sorties et à ce que les câbles de sortie et la charge soient à
l'abri de tout court-circuit. Lorsque le TR-HT est éteint, de l'énergie
résiduelle reste dans l'appareil pendant environ 2 minutes.

Le TR-HT ne possède pas de système d'isolation complet des entrées
(notamment des ports de déclenchement et de communication) et des
sorties. Par conséquent, respectez les consignes suivantes :

L'équipement informatique connecté aux ports de communication et de
déclenchement doit être alimenté en interne ou séparé de l'alimentation
secteur par une isolation double/renforcée, ou être approuvé selon la
norme CEI 60950-1. Tous les autres équipements branchés aux
déclencheurs ou à d'autres ports doivent aussi posséder une isolation
double/renforcée pour être protégés de l'alimentation secteur.

Le boîtier d'alimentation utilisé pour mettre sous tension le TR-HT doit
fournir une isolation double/renforcée pour isoler le TR-HT de
l'alimentation secteur, et le protéger des courts-circuits et des

—

13

—

«
...
11
12
13
14
15
...
»

Содержание TR-HT2 Series















































































Отзывы:

Нет отзывов

Похожие инструкции для TR-HT2 Series

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 98

Бренд: NAiS Страницы: 173

Бренд: Panasonic Страницы: 2

Бренд: ZirbenLüfter Страницы: 36

Бренд: UNITED Страницы: 8

Бренд: K'Nex Education Страницы: 56

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Abov Страницы: 138

Бренд: Absima Страницы: 5

Бренд: FUTABA Страницы: 8

Бренд: GCE Страницы: 13

Бренд: Leviton Страницы: 2

Бренд: TECH Страницы: 20

Бренд: Comunello Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды