MINI DOME COLOR CAMERA
ZC-DNT4039 NHA/ZC-DNT4039 PHA
Operation Manual
Camera adjustments
A.: Focus adjustment lever
B.:
View angle adjustment lever
C.: DIP switches
D.: DC-IRIS adjustment
E.: V-PHASE adjustment
Camera adjustments for the ZC-DNT4039NHA/PHA
DIP switch settings
The row of DIP switches allow the following settings to be made:
TDN mode
If this switch is set to “ON”, the camera automatically captures the image
in color when the subject is bright and in B/W when the subject is dark.
Auto White Balance
AWB: The camera operates in the normal Auto White Balance range
2700K~11000K
AWB EX: The camera operates in the extended Auto White Balance
range 2000K~18000K
SYNC
In LL mode, the V-Phase may be adjusted to compensate for connected
supply phase differences.
Only applicable for 24 VAC supply - otherwise the camera operates with
Internal sync.
Flickerless mode
If this switch is set to “ON”, the camera reduces flicker in the image
under fluorescent lighting.
Black Light Compensation
If this switch is set to “ON”, the camera response to strong unwanted
lighting effects behind the required subject is improved.
AGC mode
Setting to “AGC” will automatically increases the sensitivity even if the
brightness of the subject is insufficient. Selecting “NORMAL” will remove
noise from the image, but it will also limit the camera’s sensitivity.
SHARP
Setting this switch to “ON” automatically creates subject sharpness.
Day and Night
The D&N mode can be activated if TDN is set to “ON”. If set to “HI”, the
time of automatically switching to Day or Night mode will be extended.
Focus & field of view adjustment
Twist the levers on the side of the vari-focal camera to adjust the focus
and field of view settings.
TIP: If necessary, perform the final focus through the dome cover,
holding it to the lens reversed to confirm the final results.
Vertical phase adjustment
Use this adjustment when using an AC supply to align the camera
phase with that of the supply.
DC-IRIS adjustment
This is factory set and should not normally require adjustment except to
compensate for excessive image blooming.
ZC-DNT4039NHA/PHA camera specifications
Type / Format
ZC-DNT4039NHA
ZC-DNT4039PHA
Scanning Element
NTSC 2:1 Interlace
H:15734Hz, V:59.9Hz
PAL 2:1 Interlace
H:15625Hz, V:50Hz
Image Picture Element
1/3” Interline CCD sensor
Resolution (TV lines)
540 TVL (normal)
Minimum Illumination
0.08 lx @ F1.4
Exposure Control
DC Auto IRIS Lens
Flickerless
MES 1/100sec (1/120)
BLC
Central Area for DC Auto IRIS Lens
Day/Night
Burst ON/OFF & IR cut filter IN/OUT
White Balance
Auto White Balance
Auto White Balance
Range
2700°K~11000°K (normal)
2000°K~18000°K (EX.)
Sync System
Internal / Line Lock
Line Lock
(Phase Adj. Range)
0°~270°K
Line Lock
(Frequency Range)
60Hz
± 1Hz
50Hz
± 1Hz
Video Output
1.0 Vpp 75 Ohm BNC unbalance
S/N Ratio
50dB
White Clip
120IRE
Gamma Compensation
0.45
Operation Temperature
-10°C ~ +50°C (-30°C ~ +50°C with Heater)
Storage Temperature
-20°C ~ +60°C (-35°C ~ +50°C with Heater)
Power Range
DC 10.6V ~ 30V & AC 24V +/- 20%
Power Consumption
4.3W
External Dimension
140(
φ
)mm x 100(H)mm
Weight 600g
Lens Specifications
Focal Length
3.0~9.0 mm
F-No. F1.4
Iris Range
F1.4~F360
Minimum Object Distance
0.5 m
Angle Of View
Diagonal
115.4°~39.8°
Horizontal
90.3°~31.9°
Vertical
66.4°~23.9°
Lens Type
Vari-focal