Gantner GAT NET.Lock 7020 System Скачать руководство пользователя страница 60

Страница: 60 / 64

GAT NET.Lock 7020 System
Technical Data

HB_GAT-NETLOCK7020--EN_12

www.gantner.com

7.2

GAT NET.Controller S 7020 (Light)

Nominal voltage:

DC 24 V

Power supply unit

External power supply

- GAT NET.Lock 7020 (P):

GAT NET.Power Supply 100-240V / VI

- GAT NET.Lock 7020 USB (P):

GAT NET.Power Supply USB 100-240V / VI

Power consumption

- With GAT NET.Lock 7020 (P) locks:

Typ. 3 W (with 24 GAT NET.Lock 7020 locks connected)

- With GAT NET.Lock 7020 USB (P) locks:

Up to 90 W in USB charging mode

Reader types

- GAT NET.Controller S 7020 F/ISO:

MIFARE

+ ISO 15693

- GAT NET.Controller S 7020 F/ISO Light:

MIFARE

+ ISO 15693

- GAT NET.Controller S 7020 B:

LEGIC advant

- GAT NET.Controller S 7020 ICLS:

HID iCLASS

Max. locks per sub controller:

- GAT NET.Controller S 7020 F/ISO / B / ICLS:

- GAT NET.Controller S 7020 F/ISO Light:

Connectors

- Sub to master (RS-485):

RJ45

- Locks:

MOLEX, type Micro-

Fit 3.0™

- Power:

6-pin MOLEX

Interface to master controller:

RS-485

Housing material:

Plastic (ABS - VO)

Dimensions:

310 x 133 x 42 mm (12.2 x 5.24 x 1.65 in)

Weight:

Approx. 600 g (21.2 oz)

Permitted ambient temperature:

0 °C to +60 °C (32 °F to 140 °F)

Protection type:

IP 40

Protection class:

Environment class based on VdS 2110:

II (conditions in indoor areas)

Compliance:

CE, FCC, IC, ETL

Содержание GAT NET.Lock 7020 System

































































Результаты поиска

Содержание GAT NET.Lock 7020 System

Отзывы:

Похожие инструкции для GAT NET.Lock 7020 System

Бренды по названию

Популярные бренды

Gantner GAT NET.Lock 7020 System, Установка, настройка и эксплуатация

Результаты поиска

Содержание GAT NET.Lock 7020 System

Отзывы:

Похожие инструкции для GAT NET.Lock 7020 System

Бренды по названию

Популярные бренды