Gantner GAT ECO.Side Lock 7010 F/ISO Скачать руководство пользователя страница 61

Страница: 61 / 64

GAT ECO.Side Lock 7010 (NW) F/ISO
Technical Data

www.gantner.com

HB_GAT-ECOSide-Lock7010-FISO--EN_11

TECHNICAL DATA

8.1 Power Supply

Power supply:

1 x 3.6 V lithium battery, size AA, capacity 2.4 Ah

GANTNER approved battery:

EU:

Tadiran SL-860/S (Part No. 914430)

US: Tadiran TL-4903/S

Battery lifetime:

Up to 10 years* at +20 °C (68 °F)

depending on usage, configuration, and environmental conditions

8.2 Reading Field

Reader type:

MIFARE

supported types:

- MIFARE

Classic (1k and 4K)

- MIFARE Ultralight

- DESFire EV1

and EV2

ISO 15693

HID (read unique number)

Note: It is recommended to have customer-specific data carriers approved by

GANTNER before use.

Reading field frequency:

13.56 MHz

Maximum sending power:

< 500 mW

Reading field range:

5 to 35 mm (0.2´´ to 1.38´´)*

depending on the installation and type of data carrier

8.3 Wireless Interface

Frequency bands:

2400 to 2483.5 MHz

Sending power:

from -20 dBm to 4 dBm

8.4 Memory and Time Management

Data storage:

EEPROM with capacity for 150 bookings, data retained during battery
change

Internal clock:

Quartz-controlled, real-time clock

Содержание GAT ECO.Side Lock 7010 F/ISO

































































Результаты поиска

Содержание GAT ECO.Side Lock 7010 F/ISO

Отзывы:

Бренды по названию

Популярные бренды

Gantner GAT ECO.Side Lock 7010 F/ISO, Установка, настройка и эксплуатация

Результаты поиска

Содержание GAT ECO.Side Lock 7010 F/ISO

Отзывы:

Бренды по названию

Популярные бренды