gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 66

Страница: 66 / 81

SpectralLED® RS-7 USER MANUAL

Page 65

4.6.17

- FBK - Optical feedback enable/disable

Enables or disables the real-time optical feedback. Normally enabled by default, the feedback can be disabled in

order to provide direct control over the constant-current sources driving each channel.

Syntax:

FBK

report feedback setting

FBK

[0|1]

disable [0] or enable [1] feedback

Examples:

fbk

query feedback setting

fbk0

disable optical feedback (channels will be operated fixed constant-current only)

4.6.18

- FBG - Query optical feedback gain

Reports the latest optical feedback gain coefficient that is being applied to the entire LED array as a whole,

which is nominally 1.0 in the ideal situation in which all LEDs are generating precisely their calibrated level of

luminous output. Note that this coefficient continues to be updated in real time, even if optical feedback has

been disabled via

FBK

; in this case, the feedback gain figure represents the gain that

would

be applied to the

LED array, were the RS-7 permitted to be making the adjustments.

Syntax:

FBG

report optical feedback gain coefficient

Examples:

fbg

request current feedback gain coefficient

1.034

4.6.19

- SLM - Soft power limit

Reports or sets the maximum

permissible

channel operating power, as a percentage (up to 100%) of the RS-7’s

actual

capability. Attempts to command the RS-7 to drive channels beyond this limit will result in an error. Note

that channel power level adjustments being made via

CPA

coefficients and by the realtime optical feedback (see

FBK

) are not subject to this limit (they are permitted to use the headroom explicitly provided by this soft power

limit)

The default

SLM

is 90%.

Syntax:

SLM

report current channel soft limit

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 66 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: