manualshive.com logo in svg

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 62 / 81

Поделиться
Скачать
gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 62

SpectralLED® RS-7 USER MANUAL 

Page 61 

   

 

4.6.7

 

- LSN  -  LED board serial number 

Reports the serial number as stored in the LED board’s on-board read-only-memory. This serial number cannot 

be altered. 

 

Syntax: 

 

LSN

 

 

 

report LED board serial number 

 

Example: 

 

lsn 

LHX0152 

 

4.6.8

 

- USN  -  RS-7 unit serial number 

Reports the serial number as stored in the RS-7 non-volatile memory. This serial number cannot be altered. 

 

Syntax: 

 

USN

   

 

report RS-7 unit serial number 

 

Example: 

 

usn 

HX2855 

 

4.6.9

 

– ICK  -  Integrity Check 

Performs an internal check of all RS-7 parameters and calibration data, and verifies that 

a)

 

all monitored internal power supply rail voltages are within tolerance 

b)

 

all parameters are within range & structures are intact 

c)

 

stored calibration data matches the serial number of the LED board for which they were generated 

d)

 

all structures have a valid CRC (CRC32) 

 

If all goes well, only “Ok” is reported. If there are problems, each is reported with a line starting with “ERROR/” 

followed by a description. The following is a list of the possible ERROR/ codes: 

 

ERROR/VOLTAGE RAIL: [expected]V measures at [observed]V 

 

ERROR/UNIT STORED PARAMETERS: CRC or structure error 

 

ERROR/UNIT STORED PARAMETERS: appear uninitialized 

 

ERROR/LED BOARD STORED PARAMETERS: CRC or structure error 

 

ERROR/LED BOARD STORED PARAMETERS: appear uninitialized 

 

CH#x ERROR/CALIBRATION DATA: CRC or structure error 

 

CH#x ERROR/CALIBRATION DATA: missing calibration data 

 

CH#x ERROR/CALIBRATION DATA: LED board S/N mismatch 

Содержание SpectralLED RS-7


















































































Отзывы:

Нет отзывов