Gambro AK 98 Скачать руководство пользователя | Manualshive

Страница: 162 / 386

background image

A:160

AK 98 Dialysis Machine - Disinfection with the AK 98 dialysis

machine and WRO system

HCEN12745 Revision 10.2016

Program version 2.xx

11.1

General description

The AK 98 dialysis machine and the WRO water purification unit is a system that can
perform integrated heat disinfection and central chemical disinfection. An interface
cable is used to connect the AK 98 dialysis machine with the WRO unit. The cable is
ordered separately.

11.2

Integrated heat disinfection with a WRO 300 H unit

11.2.1

Description of integrated heat disinfection with a WRO 300 H unit

The AK 98 dialysis machine and a WRO water purification unit can be preset to
perform an integrated heat disinfection program. Both the dialysis machine and the
WRO unit must be preset by an authorised service technician.

The integrated heat disinfection procedure includes the following phases:

●

Heat disinfection of the AK 98 dialysis machine.

●

“Low Flow Heat” (LFH), where all wet parts between the AK 98 dialysis machine
and the WRO unit are exposed to hot water at a low flow rate.

●

Heat disinfection of the WRO 300 H unit, if this has been selected as preset on the
WRO unit.

The dialysis machine can be set to start a scheduled integrated heat disinfection.

11.2.2

Schedule an integrated heat disinfection

Procedure

1)

Check that the WRO 300 H unit is
switched on.

2)

Press the

Disinfection

button.

3)

Select the

Heat

tab.

4)

Press

Heat

or

Heat + LFH

.

11.2.3

Start an integrated heat disinfection manually

Procedure

1)

Check that the WRO 300 H unit is
switched on.

The following steps are made in the
AK 98 dialysis machine.

«
...
160
161
162
163
164
...
»

Содержание AK 98



































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AK 98

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

medialon Showmaster Go

Бренд: 7th Sense Страницы: 9

Бренд: Pari Страницы: 282

Бренд: Rane Страницы: 6

Бренд: Rane Страницы: 27

Бренд: Ranger Products Страницы: 6

Бренд: Rane Страницы: 88

Бренд: Haag-Streit Страницы: 21

Бренд: Yetter Страницы: 24

Бренд: Cooper Страницы: 10

Бренд: Korg Страницы: 32

Бренд: TECshow Страницы: 22

Бренд: Hanskamp Страницы: 22

ALFW-6LU-5KBZ Series

Бренд: Hubbell Страницы: 2

Бренд: SIMES Страницы: 8

Giotto spot 400

Бренд: SGM Страницы: 33

Бренд: VIBCO Страницы: 2

Advisor Guide Pedestrian Signal

Бренд: Campbell Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды