Gambro AK 98 Скачать руководство пользователя | Manualshive

Страница: 139 / 386

background image

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - DIASCAN

A:137

2)

Select the

Setup

tab.

3)

Press

Interval

.

4)

Select

60 minutes

,

30 minutes

or

Single

.

5)

Press

OK

to start the measurement.

Results

The result of the measuring is displayed in the clearance measurement readout field.

The clearance measurement readout field shows:

●

latest measured clearance value.

●

time of latest measuring.

●

current/estimated end of treatment Kt.

●

the

Diascan

button (opens the Diascan menu).

9.4

Check Kt/V

The dialysis machine can calculate Kt/V as a single measurement or at intervals.

If Kt/V measurement is required, distribution volume has to be set before the
measurement check takes place. The distribution volume is patient-related (based on
the patient's dry weight) and has to be properly estimated and set by the operator in
order to obtain a correct Kt/V value.

Distribution volume is the urea distribution volume in litres (water in the body),
estimated for the individual patient, and based on the patient’s dry weight. The
estimation is based on certain formulae used for this purpose, chosen by the
prescribing physician responsible for the patient. The distribution volume has to be set
by the machine operator in order for a correct Kt/V value to be obtained.

NOTE!

To get a reliable Kt/V value, it is very important that the dialysis machine calculates
with an accurate distribution volume for the patient. Therefore fill in the patient
information with care in Distribution volume.

«
...
137
138
139
140
141
...
»

Содержание AK 98



































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AK 98

Бренд: Camozzi Страницы: 2

Бренд: Oktober Страницы: 22

Бренд: Panasonic Страницы: 9

Бренд: Obdstar Страницы: 10

Бренд: Kawai Страницы: 10

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: Pari Страницы: 2

Бренд: OceanSat Страницы: 85

Бренд: Xtool Страницы: 51

Бренд: H-TEC Education Страницы: 16

Бренд: H-TEC Education Страницы: 12

Бренд: Yamaha Страницы: 46

Бренд: iHealth Страницы: 8

Бренд: Konica Minolta Страницы: 32

Бренд: Olympus Страницы: 56

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренд: Sota Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды