Gambro AK 98 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 386

Gambro AK 98 Скачать руководство пользователя страница 127

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Profiling

A:125

7.6

Set and activate profiling with a preset model

Procedure

1)

Press the

Fluid

button.

2)

Select the

UF rate

tab.

3)

Press

Profiling

.

4)

Press a preset model,

Model 1

,

Model 2

or

Model 3

.

5)

Check that the preset values in the model
are correct.

6)

Activate the profiling model. If desired, it is
possible to activate the profiling function at
any time during priming or treatment.

The parameter settings of the complete
model will be activated simultaneously. It is
possible to adjust the preset values of the
parameters when the profiling model is
deactivated, refer to Section 7.5.1

“Profiling ultrafiltration without a preset
model”

«
...
125
126
127
128
129
...
»

Содержание AK 98



































































































































































































































































































































































































Отзывы:

Нет отзывов