GALLUNOPTIMAL
Soldering Iron
SP
After switching on, the SET temperature is displayed for 1.5
seconds, then the current temperature is displayed.
Temperature indication in 5 steps. 1=100 and 5=500°C
Power indicator
Features:
Soldering iron with precise temperature control
Auto standby (0-60 minutes)
Auto-standby (0-60 minutes)
Rapid cartridge soldering tip system
Ergonomic handle, magnetic holder
Temperature adjustable via buttons on the soldering iron
Heat-resistant silicone cable with kink protection
Temperature lock function
Calibration function
Standby
Technical Data:
Input Voltage 230VAC
Power 80W
Temp. range 100-500°C
Temp. sta/- 2°C
Temp. compen/-100°C
Temp. unit °C/°F
Impedance tip-ground <0,1 Ω
Voltage tip-to-ground <2mV
OLED display 2,5cm with buttons
Connection cable silicone 1.77m total
Weight 160g
Temperatue Unit
Silicone Cover
Grid Screw
Change the cartridge soldering tip: Important NOTE!
S
witch off the device to change the cartridge soldering tip! Let the soldering tip cool down to room temperature to prevent
burns! Push back the handle pad (silicone cover) on the soldering iron and loosen the grub screw for fixing the soldering tip.
Use an optionally available silicone pad for optimum extraction and protection from any residual heat. Only original
GALLUNOPTIMAL replacement cartridges for S & 80D+ may be used and inserted into the handle! Then lightly
tighten the screw again to secure the cartridge soldering tip! Never change a soldering tip with the grub screw
tightened, otherwise the cartridge tip may be damaged when pulled out!
THANK YOU FOR PURCHASING A GALLUNOPTIMAL SOLDERING IRON. Please read the operating instructions
before operating and keep them in a safe place easily accessible to all users.
Before leaving the factory, the soldering iron is subjected to a test. This results in the soldering tip being covered
with solder and may be slightly discolored. This does not represent a defect.
WARNING
Failure to observe the following instructions may result in serious injury or death to the user.
If the device is switched on, the soldering tip automatically heats up to the last set temperature.
There is a risk of burns on the metallic surfaces!
The device is designed for soldering soft solder at different temperatures. Any other use is not permitted.
Do not touch the metallic parts on the tools during operation and immediately after switching off, CAUTION! Risk
of burns!
Do not use the device in the vicinity of flammable substances and components.
Use a heat-resistant work surface and keep your workplace clean.
Solders, fluxes and heated materials can develop harmful properties and should be exhausted in a controlled
manner. Do not inhale these toxic fumes or gases and provide adequate ventilation.
The device may only be used in dry rooms. Protect the device from liquids and moisture. Do not touch the device
with wet hands. Otherwise, short circuits and electric shocks could be triggered.
Inform other persons in the working area that the temperature can be very high during operation. Switch off the
device as soon as the work is finished to avoid danger.
Do not leave the device unattended while it is switched on.
After switching off, wait until the heated parts have reached room temperature if you want to touch or change
parts on them.
Function key
Press long to open the menu
Press briefly = Sleep mode ON/OFF
Press briefly in the menu = Enter
+ or -
In menu = next or previous submenu
In operation = increase or decrease temperature
LED
LED lights up permanently = heating up
LED flashes slowly = SET temperature has been reached
LED off = SET temperature has been exceeded
OLED screen
Digital Display
Switch on: When the mains plug is plugged in, the soldering iron will assume the last state and also stores this under voltage for
restarting. If the soldering iron was e.g. in standby, this state will be started, otherwise heat up immediately. The display shows
the actual temperature of the soldering iron tip.
Temperature: The temperature is adjustable between 100-500°C (212-932°F) with the b/-.
