manualshive.com logo in svg

GalileoSky Lite Series, Руководство пользователя

Поделиться
Скачать
GalileoSky Lite Series Скачать руководство пользователя страница 8

User Manual Galileosky Lite Trackers 

8 

 

Safe Operating Rules 

Before using the Tracker, study the instructions of GSM/GPRS devices safe maintenance. 
Make sure the polarity is correct when connecting to the power supply. 
The device should be connected straight to the vehicle battery, not to the vehicle power supply. 

ATTENTION! 

To avoid failure: 

•

 

Make sure the contacts are connected correctly! 

•

 

Unused contacts must be well insulated! 

The ground is connected to the device body. In order not to damage the tracker or the vehicle’s 
electronics, it is necessary to separate the Tracker body and the vehicle. 

Contacts Description 

 

 

 

Contact 

Description 

VCC 

Positive supply voltage 

GND 

Negative supply voltage 

IN0 

Zero analog-discrete input 

IN1 

First analog-discrete input 

IN2 

Second analog-discrete input (only for Galileosky v2.3 Lite) 

IN3 

Third analog-discrete input (only for Galileosky v2.3 Lite) 

Out0 

Zero transistor output (output 0/1) 

Out1 

First transistor output (output 0/1) (only for Galileosky v2.3 Lite) 

Out2 

Second transistor output (output 0/1) (only for Galileosky v2.3 Lite) 

CAN_H 

CAN_H contact of the CAN interface (only for Galileosky v2.3 Lite) 

CAN_L 

CAN_L contact of the CAN interface (only for Galileosky v2.3 Lite) 

 

 

 

Содержание Lite Series














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды