background image

TABLE OF CONTENTS 

 

 Page 

Specification

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

 

 

Installation 

 

 

 

Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

 

 

Mounting the Connection . . . . . . . . . . . . . . . . . . . . . .  

 

 

Ignition Noise Interference . . . . . . . . . . . . . . . . . . . . .  

 

 

Antenna  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

 

 

Tuning the Antenna for Optimum SWR . . . . . . . . . . . 

 

 

External Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

 

 

Operation 

 

 

 

Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

 

 

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   

 

 

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   

11 

 

 

Press-To-Talk Microphone . . . . . . . . . . . . . . . . . . . . .  

12 

 

 

Operating Procedure to Receive. . . . . . . . . . . . . . . . .  

12 

 

 

Operating Procedure to Transmit  . . . . . . . . . . . . . . . .  

12 

 

 

Receiving SSB Signals . . . . . . . . . . . . . . . . . . . . . . . .  

13 

 

 

Roger Beep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

14 

 

 

Alternate Microphones and Installation . . . . . . . . . . .  

15 

 
 
 
 
 
 
 

Specifications 

 

GENERAL 

 

Channels 40 

CH 

Frequency Range 

28.315 to 28.755 MHz 

Frequency Control 

Phase Lock Loop (PLL) synthesizer. 

Frequency Tolerance 

0.005% 

Frequency Stability 

0.001% 

Operating Temperature 
Range 

-30

°

C to +50

°

C  

Microphone 

Plug-in dynamic; with push-to-talk 
switch and coiled cord. 

Input Voltage 

13.8V DC nominal, 15.9V max, 11.7V 
min. (positive or negative ground). 

Transmit:

 AM full mod., 4A. 

                 SSB 25 watts PEP output, 6A    

Receiver: 

Squelched, 0.6A 

                 Maximum audio output, 1.2A

    

Size 

2-3/8” (H) x 7-7/8” (W) x 9-1/4” (D). 

Weight 

5 Ibs.  

Antenna Connector 

UHF, SO239 

Meter 

Illuminated; indicates relative output 
power, received signal strength and 
transmit power. 

 

 

TRANSMITTER 

 

Power output 

AM/FM/ 10 watts. 
SSB, 25 watts PEP. 

Modulation High-and 

low-level Class B, Amplitude 

Modulation: AM. Variable   
Frequency Modulation: FM. 

Intermodulation 
Distortion 

SSB: 3

rd

 order, more than –25dB. 

         5

th

 order, more than –35dB. 

SSB Carrier Suppression  55dB 
Unwanted Sideband 

50dB 

Frequency Response 

AM and FM: 450 to 2500 Hz. 

Output Impedance 

50 ohms unbalanced. 

Output Indicators 

Meter shows relative RF output power 
and SWR. Transmit LED glows red 
when transmitter is in operation. 

 
 

 
 
 

- 1 - 

- 2 - 

Содержание DX 88HL











Отзывы: