GAI-Tronics 723-905 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 14

GAI-Tronics 723-905 Скачать руководство пользователя страница 1

Pub. 42004-364C

GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA

610-777-1374

800-492-1212

Fax: 610-796-5954

V

ISIT WWW

.

GAI

-

TRONICS

.

COM FOR PRODUCT LITERATURE AND MANUALS

G A I - T R O N I C S ® C O R P O R A T I O N

A H U B B E L L C O M P A N Y

Model 723-905

SmartSeries Remote Subset Amplifier

Confidentiality Notice

This manual is provided solely as an operation, installation, and maintenance guide and contains sensitive
business and technical information that is confidential and proprietary to GAI-Tronics. GAI-Tronics
retains all intellectual property and other rights in or to the information contained herein, and such
information may only be used in connection with the operation of your GAI-Tronics product or system.
This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any third party.

General Information

Product Overview

The Model 723-905 SmartSeries Remote Subset Amplifier is an intelligent handset amplifier, speaker
amplifier, and FSK modem intended for use in GAI-Tronics Page/Party

®

and SmartSeries systems. The

amplifier is an integral part of GAI-Tronics desktop, desk-edge, and flush-mount stations. It has been
designed to be remotely mounted with the enclosure, allowing the associated subsets to be mounted on a
desktop, on the edge of a desk, or flush mounted. The amplifier is not designed for outdoor use and must
be mounted at an indoor location.

System Requirements and Limitations

For proper operation, the Model 723-905 SmartSeries Remote Subset Amplifier must be installed in the
Model 7245-005 Amplifier Enclosure with auxiliary inputs and used with one of the following subsets:

Single Party Subsets:

Multi-Party Subsets:

Model 726-101 Desktop Subset

Model 7265-101 Desktop Subset (5-party)

Model 711-102 Desk-Edge Subset

Model 7115-102 Desk-Edge Subset (5-party)

Model 716-102 Flush-Mount Subset

Model 7165-102 Flush-Mount Subset (5-party)

The SmartVolume

™

feature is

not

supported for Model 7265-101. Also, the SmartVolume

™

feature is

not

available for speakers equipped with L-Pads or for multiple speaker applications. The Model 723-

905 Remote Amplifier is designed

solely

for use with the magnetic hookswitch subsets listed above.

Subsets containing an RF hookswitch are

not

supported.

1
2
3
...
»

Содержание 723-905















Отзывы:

Нет отзывов