background image

17

 Installation instructions  

en-us

Importance of installing on a solid, level 
floor

Your new Gaggenau® washing machine utilizes high spin 
speeds to achieve superior water removal from your 
laundry resulting in reduced drying time. It is important to 
install your washing machine on a floor that will provide 
firm support. This prevents the washer from experiencing 
excess vibration during spinning that could cause the 
washer to move or be noisy.

The installation surface must be solid and level in both 
directions. Avoid installing your washer on soft surfaces 
such as floors with carpet or foam backed covering 
material.

If installing the washer on a wooden floor, observe the 
following:

install the washer in a corner for better support if 
possible.

if necessary, reinforce the floor by screwing a water 
resistant wooden board to the floor (minimum of 
1.18 in./30 mm thick).

Remove the transport bolts

9

CAUTION

Damage to the appliance or injury possible

The machine is secured for transport with 
transport bolts. 
Transport bolts that are not removed can 
damage the drum during operation of the 
machine, the washer will vibrate, and it will be 
much noisier during spin cycles if the transport 
bolts are not removed before use.
Be sure to remove all 4 transport bolts 
completely before first use. Keep the transport 
bolts.
If a pedestal was purchased with the washer, it 
must be installed first, prior to removing the 
transport bolts. Please consult the pedestal 
installation instructions.

In order to prevent transport damage during 
later transport, be sure to re-install the bolts 
before transport. 

1.

Remove drain hose from all brackets.

2.

Loosen and remove all 4 transport bolts. 
Remove the sleeves. Take the power cable out of the 
brackets.

3.

Place covers over the transport bolt holes. 
Four plastic covers are provided in the small parts bag 
included with your washer. Separate these covers and 
install one in each hole where the transport bolts were 
removed.  
Lock covers firmly by pressing on the snap hook.

NOTICE

Keep the assemblies together and store them for later 
use such as when moving the washer. 

Содержание WM262700

























































Отзывы: