Gaggenau CV492100, Руководство по установке, Страница: 20 / 96

20
Securing the adapter
1.
Hold the adapter at the central holder and use the
side holders to slide it towards the unit's back
panel in the base unit, then affix it.
→
Fig.
41
2.
If required, also use screws to secure it.
→
Fig.
42
Installing the appliance for air recirculation mode
with circulating-air duct
1.
For circulating-air mode, use the seal, the circulat-
ing-air duct, the diffuser and the odour filter.
2.
Observe the dimensions for the different flat duct
bends.
→ Page 16
Securing the seal
▶
Secure the seal on the flat duct elbow at a max-
imum of 5 mm from the edge.
→
Fig.
43
Inserting the flat duct elbow
▶
Insert the flat duct elbow into the outlet opening
on the rear of the appliance.
→
Fig.
44
Inserting the appliance into the worktop cut-out
▶
Carefully insert the appliance into the worktop cut-
out.
→
Fig.
45
Establishing the pipework between the
appliance and the diffuser
1.
Connect the components of the circulating-air duct
to each other.
→
Fig.
46
2.
Connect the circulating-air duct to the flat duct el-
bow on the rear of the hob.
→
Fig.
47
3.
Connect the diffuser to the circulating-air duct.
→
Fig.
48
Screwing the retaining clips in place
▶
Screw the enclosed retaining clips onto the work-
top and carefully onto the appliance.
‒
Ensure that the hob is at the same height as the
worktop and the appliance does not slip.
‒
Do not use an electric screwdriver.
→ Fig.
40
Install the appliance for air extraction mode
1.
For air extraction mode, use the seal and the
acoustics filters.
2.
Observe the instructions for the exhaust air pipe.
→ Page 18
Securing the seal
▶
Secure the seal on the flat duct elbow at a max-
imum of 5 mm from the edge.
→
Fig.
43
Establishing the piping
1.
Insert the flat duct elbow into the outlet opening
on the rear of the appliance.
→
Fig.
44
2.
If required, install additional piping elements.
Inserting the appliance into the worktop cut-out
▶
Carefully insert the appliance into the worktop cut-
out.
→
Fig.
45
Screwing the retaining clips in place
▶
Screw the enclosed retaining clips onto the work-
top and carefully onto the appliance.
‒
Ensure that the hob is at the same height as the
worktop and the appliance does not slip.
‒
Do not use an electric screwdriver.
→ Fig.
40
Connecting the exhaust air pipe
1.
Secure the exhaust air pipe to the flat duct bend.
2.
Establish the connection to the exhaust air open-
ing.
3.
Seal the joints appropriately.
Connecting the cables to the appliance
1.
Connect one of the longer cables to the appliance
and to any control knob.
→
Fig.
49
2.
Ensure that the plugs snap into place in the sock-
ets.
Inserting filters
Note:
For circulating-air mode, insert the odour fil-
ters.
For air extraction mode, insert the acoustics filters.
1.
Observe the filters' air flow direction.
2.
Insert two of the filters into the left and right of the
appliance, and slide them forwards.
→
Fig.
50
3.
Insert the other filters into the left and right of the
appliance.
→
Fig.
51
Inserting grease filters
▶
Insert the grease filter.
→ Fig.
52
Positioning the ventilation grille
▶
Position the ventilation grille.
→
Fig.
53
Establishing the connection to the power
supply
1.
Observe the connection data on the rating plate.
2.
For 3 N, connect the cable to the mains socket in
accordance with the figure.
→
Fig.
54
3.
For 2 N, connect the cable to the mains socket in
accordance with the figure.
→
Fig.
55
4.
For 1 N, connect the cable to the mains socket in
accordance with the figure.
→
Fig.
56
5.
For 2 L/2 N, connect the cable to the mains
socket in accordance with the figure.
→
Fig.
57
6.
Note the colours of the cables.
– BN: Brown
– BU: Blue
– GN/YE: Yellow and green
– BK: Black
– GY: Grey
7.
If required, arrange the supplied wire end ferrules
differently depending on the type of connection.
8.
To connect two cables, if required, use a wire end
ferrule.
‒
Shorten the wires.
‒
Remove the insulation.
Checking the function
1.
Switch on the appliance.